铝合金可用于包边，或彩钢板的剩余部分可直接用于封边。彩钢复合板的长度、宽度、角度等尺寸应先确定;其次，将封边材料制成相应的附件;最后，使用防水拉铆钉固定边缘材料。
Aluminum alloy can be used for edge banding, or the remaining part of color steel plate can be directly used for edge banding. The length, width, angle and other dimensions of color steel composite plate shall be determined first; Secondly, the edge sealing material is made into corresponding accessories; Finally, secure the edge material with waterproof pull rivets.
彩钢复合板施工中应注意的问题
Problems needing attention in the construction of color steel composite plate
1.首先检查施工图上的尺寸标记，检查施工位置的尺寸是否与图纸比例一致。检查尺寸时，局部尺寸偏差不大于或小于25mm，墙底高度偏差不大于或小于10mm。
1. First check the dimension mark on the construction drawing and check whether the dimension of the construction position is consistent with the drawing scale. When checking the dimension, the local dimension deviation shall not be greater than or less than 25mm, and the wall bottom height deviation shall not be greater than or less than 10mm.
2.搬运材料时，应采取相应的保护措施，避免运输过程中材料的碰撞和损坏。卸载材料时，应将其放置在每个施工点，并小心搬运，以防止损坏材料。材料摆放整齐后，应仔细检查材料的外观、尺寸和焊接质量。
2. When handling materials, corresponding protective measures shall be taken to avoid collision and damage of materials during transportation. When unloading materials, they shall be placed at each construction point and handled carefully to prevent damage to materials. After the materials are placed neatly, the appearance, size and welding quality of the materials shall be carefully checked.
3.根据图纸尺寸和要求，用膨胀螺丝等附件将底盘铁固定牢固，然后组装彩钢卡箍。装配时，拧紧所有螺钉，检查其钢梁是否在垂直方向，在同一平面内，其构件尺寸是否符合要求。
3. Fix the chassis iron firmly with expansion screws and other accessories according to the dimensions and requirements of the drawing, and then assemble the color steel clamp. During assembly, tighten all screws, check whether the steel beam is in the vertical direction, in the same plane, and whether the component size meets the requirements.
4.安装时应保证地面、板面平整，墙、地、顶等面结构设计合理，以保证安装的严密性。如果在安装过程中遇到拐角，则应将其视为圆角。
4. During installation, the ground and plate surface shall be flat, and the structural design of wall, ground and top shall be reasonable to ensure the tightness of installation. If corners are encountered during installation, they shall be regarded as rounded corners.
不管是对济南彩钢复合板进行包边，还是说安装复合板时，都需要首先确定其尺寸，并且与工程图纸保持一致。包边时通常使用铝合金材料或者彩钢板的剩余材料，安装过程一定要注意相关事项，避免二次伤害。
Whether it is to wrap the edge of Jinan color steel composite plate or to install the composite plate, it is necessary to first determine its size and keep it consistent with the engineering drawings. Aluminum alloy materials or residual materials of color steel plate are usually used for edge wrapping. Relevant matters must be paid attention to in the installation process to avoid secondary injury.
以上的精彩内容来自：山东超光耀金属材料有限公司彩钢复合板产品的介绍及分享，更多内容请继续关注我们：http://www.sdcgy.com
The above wonderful content comes from the introduction and sharing of color steel composite plate products of Shandong chaoguangyao metal materials Co., Ltd. please continue to pay attention to us for more content: http://www.sdcgy.com
